
Types of fire damper explained: what you have and how it should be tested
Every fire damper does the same job. How it does that job varies a lot.
Some close under gravity when a metal link melts. Some swell into a solid plug of char, and others are driven shut by a motor taking its signal from the fire alarm panel. Knowing which types of fire damper sit in your ductwork decides how they get inspected, how long a visit takes and what a fair quote looks like.
It also tells you which faults an engineer is likely to find. This guide walks through the main types you will meet in commercial buildings, where each one tends to be fitted, and the testing each type needs to stay compliant.
Why the type of fire damper matters for compliance
Fire dampers sit wherever ductwork passes through a fire-resisting wall or floor. When a fire starts, they close that gap in the compartment line so smoke and flame stay on one side for the rated period. Design guidance for this sits in Approved Document B Volume 2, which covers fire safety in buildings other than dwellings.
The law then asks for upkeep. Article 17 of the Regulatory Reform (Fire Safety) Order 2005 requires the responsible person to keep fire safety equipment in efficient working order under a suitable system of maintenance. A damper that is painted shut, blocked by cabling or hidden behind a sealed ceiling fails that test, whatever type it is.
Type matters because each one fails in its own way. A curtain damper with a seized blade, an intumescent grille clogged with dust and a motorised damper with a dead actuator all need different checks to find them.
Curtain fire dampers
Curtain dampers are the most common type in older commercial ductwork. A folded stack of steel blades sits at the top of a frame, held open by a fusible link. When the air in the duct reaches the link’s rated temperature, usually around 72°C, the link breaks, and the blades drop under gravity or spring tension to seal the opening.
They are simple, cheap and reliable when looked after. The trouble is that they sit out of sight for years, and dust, corrosion and nearby building work all take a toll.
How curtain dampers are tested
Testing a curtain damper is hands-on. The engineer opens the access panel, releases the link or catch, and watches the blades drop and lock fully closed. They then reset the damper, fit a new link where needed and record the result with before and after photographs. This is the drop test most facilities managers will have heard of.
Typical faults include blades that stick halfway, weak or corroded springs, and links that someone has wired open. Missing access panels cause the most delay on site, because the ceiling or duct has to be opened up first.
Intumescent fire dampers
Intumescent dampers work with no moving parts at all. They use a material that expands rapidly when heated, filling the airway with a dense, insulating char. You will usually find them in transfer grilles through walls and doors, and on some low pressure ventilation runs.
How intumescent dampers are inspected
With nothing to release, inspection is visual. The engineer checks the intumescent strips are present, intact and free from paint, grease or heavy dust that could slow the reaction. They also confirm the unit suits the opening and is properly sealed into the wall around it.
Kitchens, plant rooms and workshops need closer attention. Grease and grime build up faster there, and a coated grille may react too slowly to hold back a fire.
Motorised fire dampers and fire and smoke dampers
Motorised dampers swap the fusible link for an electric actuator. The actuator holds the blade open while powered and springs it shut when power is cut, usually on a signal from the fire alarm or building management system. Many also carry a thermal trip, so the damper still closes on heat if the signal never arrives.
Where a damper also has to hold back smoke, it is normally a combined fire and smoke damper, tested against the smoke control standard as well as the fire standard. You will find these in newer offices, hospitals, student accommodation and any building with a designed smoke control strategy.
How motorised dampers are tested
Testing covers the damper and the system it talks to. The engineer cycles the actuator, confirms the blade closes and reopens fully, and checks the end switches report the correct position back to the panel.
Cause and effect testing with the fire alarm contractor then proves the right dampers close when a given detector activates. Some systems allow remote testing from the BMS, which cuts disruption on occupied floors, although a physical check on a regular cycle is still good practice.
How often each type of fire damper should be tested
BS 9999 calls for fire dampers to be tested at regular intervals by a competent person. Annual testing has become the accepted benchmark across the industry, with more frequent checks for spring operated dampers and those in dusty or greasy areas. Many insurers and facilities contracts now write the annual test in as standard.
The type of damper shapes what that annual visit looks like:
- Curtain dampers: a physical drop test and reset of each unit
- Intumescent dampers: a visual inspection, with cleaning or replacement where the strips are coated or damaged
- Motorised dampers: an actuator cycle, a position feedback check and a cause and effect test with the alarm system
A building with a mix of types needs a schedule that reflects this, so the right engineer and the right time allowance turn up for each area. Our guide to fire damper service in the North West covers what the inspection report itself should contain.
Building a fire damper register you can rely on
Most problems we see start with poor records rather than poor dampers. A good register lists every damper by unique reference, with its location, type, access route and last test result. Photographs taken during each test give you evidence that stands up to an auditor, fire officer or insurer.
When the register is missing or out of date
Buildings that have changed hands or been refitted often have patchy records. In that case, the first visit works as a survey as much as a test. The engineer identifies each damper, notes its type, tags it and flags any that need access panels fitting.
It is worth budgeting for this once. From then on, every annual visit is quicker to plan and easier to price. Where a damper fails and cannot be repaired, our guide to fire damper replacement explains the next steps.
Fire damper inspection and testing with Thor Fire
Knowing your types of fire damper turns a vague compliance task into a plan you can price and schedule. Curtain dampers need drop testing, intumescent units need a clean visual check, and motorised dampers need testing alongside the alarm system they rely on.
Thor Fire carries out fire damper inspection, testing and remedial works across the North West, Merseyside, North Wales and the Midlands, with engineers based in the areas we cover. If you are unsure what is fitted in your building, or your register needs rebuilding, call us on 0161 339 7736 or get in touch online. We will tell you what is there, what it needs and what it will cost before any work starts.
